- #Verizon wireless um150 usb modem driver download drivers
- #Verizon wireless um150 usb modem driver download upgrade
- #Verizon wireless um150 usb modem driver download code
If Aruba field engineering teams or customers procure modems that are not part of these list, please inform Aruba HQ or use Aruba‟s Airheads Online forum to
#Verizon wireless um150 usb modem driver download drivers
As new hardware and drivers for modems become available, Aruba will attempt to keep this list up-to-date.
Summary This document is expected to cover the use of most USB cellular modems. If the RAP is still unable to communicate over cellular backhaul, please contact your Aruba engineer/ support service. In this case, the modeswitch command would be (ArubaM3-86) (AP provisioning) #write memory (ArubaM3-86) (AP provisioning) #reprovision ap-name (ArubaM3-86) (AP provisioning) #usb_modeswitch "-v -p -V -P -M " Login to the controller CLI via SSH or telnet and enter the following commands: Sample results for a “Verizon UMW 190 modeswitch parameters” search are below. RFE 1381 - Configuring USB cellular modems for RemoteAPs 5)įirst, search for the modeswitch parameters of the particular hardware model of cellular data-card on the internet. This can be done on the controller CLI starting ArubaOS 5.0.2. Ideally, USB cellular devices should register with the RAP as modems, but occasionally they register as a mass-storage device. Generic USB devices may be mass-storage or they may be modems. Verify (3).Ĭase 3) NOTE: If the RAP still does not work, the USB cellular modem may require a mode-switch. This should allow the RAPs to operate with most USB-cellular cards. Fill those parameters in the corresponding fields under USB Parameters for that RAP. Look for the configuration parameters for that modem in the table in Appendix 1. If the USB model does not appear in the drop-down list, select „Other (Any)‟ for Device. Refresh the „AP Provisioning‟ screen to ensure the RAP comes back with a „C‟ flag, indicating cellular RAP. When the AP comes back up, disconnect the Ethernet. While having the USB modem still plugged in, click “Apply and Reboot”. Check “USB parameters", and under „Device‟ select the USB from the dropdown list. Select the AP that requires provisioning. It would show up in the list under AP Provisioning.
Steps to configure cellular backhaul for a RAP are as follows: 1)īring the RAP up on Ethernet backhaul for the first time with the USB modem plugged in. RFE 1381: RFE 1381 provides an additional command called „usb-modeswitch‟ to load configuration parameters hitherto unknown to the controller. If the device driver is available but the provisioning parameters are unknown, this document would help configure those parameters on the controller and push them out to the RAPs.
#Verizon wireless um150 usb modem driver download code
ArubaOS code comes pre-loaded with device drivers for the most common hardware types. RFE 1381 aims to ease this configuration process without requiring a controller reboot with ArubaOS 5.0.2 and newer.ĭescription: In order to enable cellular uplink for a RemoteAP (RAP), the RAP needs to have two main components- a device driver for the USB data card and the correct configuration parameters.
#Verizon wireless um150 usb modem driver download upgrade
The requirement is to allow configuration of specific parameters by field engineers without requiring a controller code upgrade or reboot. Problem Statement ArubaOS 5.0.1 and prior versions allowed the user to only use NICs that are previously known and whose configuration parameters are coded in ArubaOS. Gokul Rajagopalan Version 1.0 – Aug 30, 2010.Ĭopyright © 2010 Aruba Networks, Inc. RFE 1381 - Configuring USB cellular modems for RemoteAPsĬontents Problem Statement.